01. |
General Requirements |
14% |
|
0101. Permits Required
Determine when permits are required and issues permits. |
1% |
|
0102. Piping Protection
Inspect all piping systems to insure protection as required from corrosion, stress and strain, freezing, and physical damage. |
3% |
|
0103. Piping Installation, Support, Sleeving and Penetrations
Inspect all piping systems for proper installation, support, sleeving, penetrations and waterproofing of exterior openings. |
4% |
|
0104. Damage to Structural Elements
Inspect building components for damage due to installation of the plumbing systems. |
3% |
|
0105. Required Test of Plumbing Systems
Verify that all required tests of installed piping systems are conducted. |
3% |
|
|
|
02. |
Fixtures |
8% |
|
0201. Maximum Required
Inspect for proper location and the minimum required fixtures. |
1% |
|
0202. Fixture and Material Approvals
Inspect for approved materials and fixture approvals. |
1% |
|
0203. Installation, Location, Clearance and Access
Inspect for proper installation of fixtures, waste receptors, appliances and appurtenances including clearances, access and sealing. |
3% |
|
0204. Flow Rates
Inspect for maximum and minimum flow rates and temperature control valves. |
2% |
|
0205. Faucets, Fittings and Accessories
Inspect for proper installation of faucets, fixture fittings and accessories. |
1% |
|
|
|
03. |
Water Heaters |
12% |
|
0301. Uses, Installation and Labeling
Inspect for proper use and installation of materials and check for appliance approval. |
2% |
|
0302. Clearance, Location, Protection, Pans, Seismic Restraint
Inspect for clearances, locations, protection, pans and seismic restraint. |
3% |
|
0303. Valves and Expansion Tanks
Inspect for required valving, T&P valve and discharge piping installation, thermal expansion requirements and pipe sizing. |
4% |
|
0304. Combustion Air and Gas Piping
Inspect for proper sizing of fuel gas piping, combustion air requirements and required venting. |
3% |
|
|
|
04. |
Water Supply and Distribution |
21% |
|
0401. Materials, Joints and Connections
Inspect for approved materials, joints and connections. |
3% |
|
0402. Identification, Sizing and Valving
Inspect the service and distribution piping for proper installation of cold and hot water delivery, identification, sizing and valving. |
7% |
|
0403. Protection Against Contamination
Inspect the potable water supply and distribution piping for proper protection against contamination. |
6% |
|
0404. Pressure and Volume Requirements
Verify the minimum and maximum pressure and volume requirements. |
3% |
|
0405. Potable Water and Treatment
Verify the requirements for potable water and installation of water treatment. |
2% |
|
|
|
05. |
Sanitary Drainage |
23% |
|
0501. Materials and Fittings
Inspect for approved materials and use of proper fittings, joints, and connections. |
4% |
|
0502. Sizing of System
Inspect for proper sizing and installation of the building drain, building sewer, branches and stacks. |
8% |
|
0503. Valves, Sumps, Ejectors, and Cleanouts
Inspect for the proper installation of backwater valves, sumps, ejectors and required cleanouts. |
3% |
|
0504. Traps
Inspect for the correct type, size, design, location and installation of traps. |
5% |
|
0505. Indirect Waste
Inspect indirect waste systems for air breaks or air gaps. |
3% |
|
|
|
06. |
Vents |
22% |
|
0601. Material, Joints, Connection and Grade
Inspect for approved materials, joints, connections and proper grades. |
5% |
|
0602. Seizing
Inspect for the proper sizing of the venting system. |
6% |
|
0603. Methods and Installation
Inspect for the minimum venting requirements, methods and installation. |
11% |